A 22 kW Generac standby generator:
Brian in Holmdel, NJ had Green Sun Energy Services install a Generac 22/21 kW natural gas standby generator in October of 2026. The system was sized for 1,700 square feet of living space and is served by a 150-amp electrical service.
The transfer arrangement is a managed whole-house setup using a 150-amp service-entrance-rated automatic transfer switch — Generac Model G0099310 — with an integrated surge protection device. When JCP&L power goes out, the switch detects the outage, signals the generator to start, and transfers the full load automatically. Because it is a whole-house configuration, Brian does not have to decide which circuits stay live — everything comes back on. One Load Management Module is wired in to handle one 60-amp device; if the generator’s demand approaches its limit while that load is running, the module sheds it automatically and restores it once headroom allows, without any manual intervention.
The generator itself is the Generac Next Generation Air-Cooled model, Model 7260, rated at 22 kW on liquid propane and 21 kW on natural gas — here running on natural gas. Connectivity is built in: the unit includes cellular, Wi-Fi, and Bluetooth capability so Brian can monitor status and receive alerts remotely. The generator sits on a 5,000 PSI precast concrete pad (54″ x 32″ x 3″, 190 lbs). The package included up to 20 feet of electrical and 20 feet of plumbing runs.
The grounding work followed NJAC 5:23-3.16: two grounding rods and an intersystem bonding bridge were installed, along with two water-main bonding clamps and a run of #6 AWG copper from the water main to the service main. A #6 AWG green-jacket copper ground wire was also part of the installation.
The system is backed by a 5-year limited warranty from Generac and a 5-year limited workmanship warranty from Green Sun Energy Services.
Brian also enrolled in a generator service plan that includes an annual maintenance visit and an extended parts-and-labor warranty, so the generator will be looked after on a regular schedule going forward.
Why Holmdel homeowners choose Green Sun Energy Services
Complete backup power, from sizing and installation to the service that keeps it ready.
What makes Green Sun Energy Services different
- Standby generators: installed and serviced as a Generac Authorized Sales and Service Dealer, by factory-authorized Generac technicians. On this home: a Generac 7260 standby generator (22 kW LP / 21 kW NG) running on natural gas, on a 150-amp transfer switch (managed whole house) and serviced by Green Sun Energy Services.
- Warranty: backed by a 5-year generator workmanship warranty.
- Local: locally owned and operated in New Jersey since 2010, NJHIC licensed (#13VH06229000), with 449 completed standby generator projects across Monmouth County and 626 standby generator projects throughout New Jersey.
Our work in Holmdel
Green Sun Energy Services has completed 27 standby generator installations and 43 generator service customers in Holmdel. Holmdel, a township in Monmouth County, is served by JCP&L.
Thinking about a standby generator for your Holmdel home? Tell us about your project here or call 732-410-7818.
Power it. Protect it. Maintain it.
Project Facts
- Location
- Holmdel, NJ
- Services
- Standby Generator Installation, Standby Generator Service
- Client since
- October 2026
- Manufacturer & model
- Generac 7260
- Rated output
- 22 kW LP / 21 kW NG
- Fuel
- Natural Gas
- Home sized for
- 1,700 sq ft
- Electrical service
- 150 amp
- Transfer switch
- 150 amp
- Load management
- Managed Whole House
- Workmanship warranty
- 5 years
Standby generator questions from Holmdel homeowners
Do generator requirements in Holmdel differ from the next town over?
The manufacturer's equipment requirements do not change when you cross a municipal boundary into Holmdel, but local zoning can. A township may impose its own side-yard and rear-yard setbacks, mechanical-equipment rules, screening, noise requirements and floodplain provisions. That is why every property gets a municipal zoning review rather than a general answer.
Can the generator be connected to any nearby gas pipe?
No. The branch supplying the generator has to be sized for the flow and pressure the machine needs. A pipe that happens to be close by may be too small, or may already be carrying too much load. Undersized piping shows up as poor starting, unstable running, reduced output or a generator that shuts down under load.
What does remote monitoring actually tell you?
Depending on the generator and the connectivity, remote monitoring can report status, maintenance notifications, alarms, exercise information and operating history. Its real value is that a fault announces itself between service visits, instead of being discovered during the outage it was bought for.